|
HOT STREET is a heads-up class for all types of vehicles. Rear suspension may utilize ladder
bar or four-links (no full tube chassis). This class is for the unassisted cars that can still motivate
down the 1320 in a very quick time. All entries compete on a Mickey Thompson
(29.5 x 10.5 Slick or 30 x 13.5 ET Street) or any other brand as long as the
tire is not larger (height &
width) than the M/T
HOT STREET Class Guidelines:
BODY:
The car must retain its original appearance and profiles. Aftermarket fiberglass replacement
panels are limited to hood, front fenders, doors, deck lid and bumpers. One piece front ends are
permitted, but must retain factory un-altered grill, head lights and bumper.
Front Grille:
Complete
factory un-altered grille is required. Grilles may be covered, but with
only clear tape or clear Lexan or Plexiglas, and must have prior
approval from a PSCA Official.
Rear Wing / Spoiler:
Aftermarket
wings and spoilers are permitted, but may not extend more then 16 inches
from the transition point with the body to the tip of the wing.
FIREWALL:
Must retain in original factory location, and be constructed out of
sheet-metal. Notching of factory firewall for valve cover clearance is
allowed.
HOOD / SCOOPS:
Scoop
or cowl may not exceed more than 9 inches at the highest point of the
air inlet opening above the height of the original hood surface.
INTERIOR:
Dash board must be stock appearing and in stock location. Door panels must be
covered or painted. Carpet and or upholstery is required to cover the flooring and tunnel where
visible.
Headliner is not required.
SEAT LOCATION:
Two front full size bucket seats, or one bench seat with upholstery required.
Seats must remain in the stock location.
WINDOWS:
Must be of safety glass, Lexan, or other shatterproof materials, minimum 1/8th inch
thick. Also must be clear and non hazy.
BRACKET RACING AIDS:
The use of bracket racing aids such as optical sensors, delay boxes,
stutter boxes, and throttle stops are not allowed. No object can be
mounted anywhere forward of the front tires to trip any of the race
tracks timing systems.
CHASSIS / SUSPENSION
FRONT SUBFRAME:
All
sub framed or full framed cars must retain complete stock front subframe
from firewall forward. Frame connectors or rear frame rails may not pass engine firewall, except for
the following exceptions. The 62-67 Chevy II's and 64 1/2-68 Mustangs and similar cars with bolt-on
front K-members, must retain stock or aftermarket bolt-on front subframe. The subframe must be a
bolt on (not welded, unless kit is OK by PSCA officials) to factory mounting location. Frame connectors or rear frame rails may pass
firewall location, but not exceed where original front subframe mounts to the body. All late model
Mustangs must retain factory front subframe from firewall forward. Stock or direct fit aftermarket
K-members are permitted, but must be bolted in factory location using factory bolt holes. Cross
members on all front sub frames may be altered or removed for oil pan clearance.
FRONT SUSPENSION:
All cars must retain stock suspension, aftermarket tubular control arms,
coil over kits, or OEM front strut retrofits are permitted. But must be a direct bolt on, no welding
modifications permitted. Aftermarket Racing Struts with spindle mounts or hub mounts designed
for tube type front ends are prohibited. Stock wheelbase will be enforced on all vehicles.
**The only front suspension bolt-on kit deemed legal by the PSCA are the CHRIS
ALSTON's "No Fab", AJE, HEIDTS, Smith Racecraft, TCI and *FATMAN bolt-on kits
(
Nova's, Camaro's & early Mustangs) & The Rod & Custom Motorsport Mustang II kit for 64 1/2-66 Mustang, Part #RC-106. Kits must be installed as instructed.
DRIVE TRAIN
AUTOMATIC TRANSMISSIONS:
Automatic transmission originally produced by any American
automobile manufacturer are permitted. Transmission-to-engine adapters are permitted. Aftermarket torque converter, trans-brake, shift kit,
valve body, shifter, and pan cooler use are permitted. (*see
weight breaks).
MANUAL TRANSMISSION:
*Aftermarket
Manual Transmissions (Clutchless Jericho & G-force versions) are
allowed in Small
Block applications only with weight adds. Lenco, JEFFco,
Clutchflites, or
Clutch Hydros are not permitted. All shifts must be made manually
without the aide of aftermarket electric or pneumatic devices. (*see
weight breaks).
REAR END:
Any rear end is allowed including Fab 9.Spools, aftermarket axles, and any gear
ratios are allowed.
ENGINE:
There is a
470ci limit for small blocks and a 555ci limit for big blocks. There are no
restrictions on internal engine modifications.
BLOCK:
Aftermarket iron or aluminum blocks are permitted.
EFI:
(Electronic Fuel Injection) Any EFI or digital fuel injection are permitted.
ENGINE MOUNT LOCATION:
The maximum allowable engine setback from the center line of the
number-one spark-plug hole to the center line of the front spindle is 2 inches, except in those
vehicles in which the engine was factory installed at a distance greater than 2 inches behind the
spindle. In such cases, the engine set back may be no further back than the original location.
HEADS:
Two valves per cylinder maximum. The following are cylinder heads restrictions
(1) Splayed, symmetrical, or canted valve small block heads *see
weight penalty
(2) Hemispherical heads are prohibited (unless factory or factory style replacement)
(3) One spark plug per cylinder Max
(4) All billet cylinder head prohibited
INTAKE MANIFOLD:
No
restrictions.* See add weight section.
EXHAUST:
Production type mufflers
or collector type mufflers are required. No collector inserts permitted. Modification or
removal of muffler internals is prohibited (no gutting).
FUEL / FUEL SYSTEMS
Hot Street will be requiring a "Spec Fuel" for
2008... More Details By Dec 14th
IGNITION:
No restrictions.
OILING SYSTEM:
Any oiling system is permitted. The front cross member may be altered for oil
pan removal. Vacuum pumps are acceptable.
ON BOARD DIAGNOSTICS / DATA RECORDERS:
On board diagnostic computers and recorders
are permitted. Memory and playback tachometers are allowed.
PARACHUTE:
Must meet NHRA requirements
RADIATOR:
An automotive-type radiator is required.
STEERING:
After market rack-and-pinion is allowed.
STREET LEGAL REQUIREMENTS:
All entries are required to have two working headlights and two
working tail lights (headlight doors must be fixed open or work manually or automatically on cars
so equipped). Brake lights, turn signals not required to operate.
TIRES:
Front tires must have a minimum tread width of 4.5 inches. Front tires do not have to be
DOT approved. Rear tires, all entries compete on a Mickey Thompson
(29.5 x 10.5 Slick or 30 x 13.5 ET Street) or any brand as long as the
tire is not larger (height &
width) No Drag Radial Tires permitted...
Hot Street WEIGHT GUIDE:
(All weights are race-ready car with driver)
BASE WEIGHT
4 cly 2300lbs
V/6's 2450lbs
SMALL BLOCKS Up to 329ci / 2550lbs
SMALL BLOCKS
330 - 356ci / 2600lbs
SMALL BLOCKS 357 - 400ci / 2650lbs
SMALL BLOCKS
401 - 440ci / 2750lbs
SMALL BLOCKS
441 - 470ci / 2850lbs
BIG BLOCKS
Up to 510ci / 3025lbs
BIG BLOCKS
511 - 555ci / 3125lbs
ADD WEIGHT (In Percent of your Engine Cubic Inch
Displacement)
10% For use of a Sheet
Metal, or any Fabricated type Intake Manifold
10% For use of a
"Dry Sump" Oiling Systems
30% For
Manual Trans
(Clutch Version) in Small Blocks
40% For Manual Trans (Clutchless Jericho) in Small Blocks
60% For Manual Trans (G-Force) in Small Blocks
15%
Small Blocks using CFE "Pro King", Edelbrock
"Victor II", GM "SB-2" Castings, or any
GM 15 Degree
(GM Part # 24502615) or similar "Comp Eliminator" Style Heads
20% For Small Blocks not using
"True Wedge" or any "In-line Valve" Heads.
Example Yates
or Edelbrock High Port (part
#'s 6049SC1 & 6049C3H)
or GM Symmetrical
15%
Big Block Cylinder Heads (That are +/- 3 Degrees From Factory Valve
Angle)
20% For Big Block Ford
C
& E Motorsports Cylinder Head.
40%
For Big Block Ford
C
& E Pro-Filer Cylinder Head.
40% For Big
Blocks that use
Big Chief, Big Duke, Pontiac, Olds, Symmetrical and/or any
non conventional cylinder
heads other then listed. DEDUCT WEIGHT (In
Percent of your Engine Cubic Inch Displacement)
10% For
Single Carburetor Applications
10% For
Pre-74 Full & Mid-size Entries
15%
For a
2-speed Automatic Transmission
10%
For a 3-speed Automatic Transmission (Other than a Pro Trans, A-1, Scott
McClay
or similar light-weight
Torque-Flight,
TH200, TH350, etc...) Figuring
out your Weight:
You need to know how many cubic inches your engine is and a calculator to
make it easier... For example you have a 550ci Big Block(3125lbs) with
Sheet Metal Intake(+10%), Dry Sump(+10%) and a Power-Glide
Transmission(-15%) Total up your weights adds and subtract your weight
deducts....You would take your Cubic Inch multiply by the amount Adds or
Deducts and come up with your PSCA Race Weight......Example for above...
Add 10% + 10% - 15% which equals a total of 5%.. Take that 5%x 550 which equals
27.5lbs, add that to your 3125 Base Weight (27.5 + 3125 ='s 3,152.5lbs) Your
PSCA RACE WEIGHT WILL BE 3,153lbs....We will round up all figures to the nearest
pound.. If anyone has any trouble figuring out your weight for
your combo, you can contact Mel at 661-609-9486 and I will assist you... WHEEL BASE:
Must retain stock wheel base with a maximum variation from left to right and front
to back of one inch.
WHEELIE BARS:
Wheelie bars permitted
PSCA Required Decals:
Class Sponsor Decal
Edelbrock Hot Street decal must be installed on base of windshield on the
passenger side. (Bottom left hand side when looking at front of vehicle
windshield)
Series Sponsor Decal
TBA decal must be installed on base of windshield on the
drivers side. (Bottom right hand side when looking at front of vehicle
windshield)
Contingency Program & Contingency
Decals:
In order to become eligible for PSCA official contingency
program, You must first become a member of the PSCA. You can do this at
the PSCA Event Trailer during registration or on-line at the PSCA Store.
All contingency decals may appear anywhere on the windows in a clear and
organized fashion. Contingency decals may not be overlapped or modified.
Most decals are available at the PSCA Event Trailer, but in the event
the PSCA does not have the decals in stock, it is the racer's
responsibility to obtain the proper decals to be eligible for the
Contingency payout.
Penalties
For Violating any PSCA Class Rules:
Penalties will vary for any PSCA Class Rule violation's from
Championship Point Deduction, Race Suspension, Probation and/or
Re-instatement Fine (Paid to St Jude In the name of the PSCA) If you are
in any violation that directly effects car performance (Example: Over
CI, Illegal Power Adders, etc..) You can receive the Maximum Penalty
(Disqualification from Event with loss of 50 Championship Points,
Two-Race Suspension and a $500 Re-Instatement Donation) You will also be
listed on a Web Page for all to view what violation and penalty any
racer receives..
RACE DAY
POLICY'S
SCALES:
After each qualifying and elimination
pass, all cars must stop and weigh at the track scales. If you lose in
eliminations, and your opponent fails to make weight you will be
reinstated into the eliminations only if you made minimum weight
requirements. If both cars failed to make minimum weight, both cars will
be disqualified. It is the driver's responsibility to verify with each
track scale, the weight of his/her car prior to each race day. There
will 5lb error factor allowed.
Alternating Lanes During
Qualifying:
Each Hot Street driver
must alternate lanes during qualifying. Even if you skip a session, you
must run the opposite lane you made your previous run in. If you choose
to ignore this rule, your second consecutive pass in the same lane will
be disqualified. Entering
into a 2nd Class:
During
qualifying, any PSCA racer who purchases a 2nd NHRA Tech Card and pays
entry into an additional class will be able to do so. However, once your
Final Hot Street Qualifying Session is Completed, you are no longer able
to make runs in that 2nd class... This also means NO RUNS in the Sunday
Morning Bracket Time Trials Session.
TOW BACK &
TOW VEHICLES:
All Hot Street entries are allowed to tow
to staging lanes and after the track scales. All are subject to be searched by a PSCA Official at any time.
BYE-RUNS:
All vehicles must take the tree, and run down the 1/4 mile.
PSCA
Race Day Rules and Procedures...Click Here
All
drivers and vehicles must meet current NHRA and track requirements.
For questions or more
information on these rules, please contact Mel Roth at 661-609-9486
Rules
do not become official until Jan 1st 2008...
2nd in 2007 Championship Points, Adrian Duran
3rd in 2007 Championship Points, Brian Cobbett
4th in 2007 Championship Points, Team "No-Juice"
5th in 2007 Championship Points, Dan Bott II
|
